4CELNK-YR OR3V Large Capacity 6-pc Kit (2018-027-104)

Are the Base Kit and Expansion kits STILL not enough capacity for you? Well, upgrade to these! You add another back-side wiring pocket, that lets you separate some into a more-permanent wiring area. Perfect for those shakers that never come off, or that USB cable that charges the phone: cables you want “in there”, but out of the way so that your configuration changes don’t pull those out too.

Click or tap below to view detailed item pages and purchase 4CELNK-YR for your rig

Grand-Opening SALE: 20% off all 4CELNK-YR!

BUY NOW: Show purchasing options and details...

During our early days, we're offering you a 20% off-the-top product discount, calculated at check-out.
Welcome and Thanks! (LFE brackets excluded, since they've been out for years now) Discount offer subject to change at any time.

 

Tap the photos or links to view more item details.

4CELNK-YR OR3V Large Capacity 6-pc Kit - BLK

MSRP: $31.49

Grand-Opening SALE: 20% off all 4CELNK-YR!

4CELNK-YR OR3V Large Capacity 6-pc Kit - WHT

MSRP: $31.49

Grand-Opening SALE: 20% off all 4CELNK-YR!






Made to fit oZone and R3volution sim rigs


View More...


Finally! Gaming rig cable management that's easy to put on, easy to change, and easy to live with. Imagine: no more cutting and replacing wire-ties. No more scratching the rig. Now you can have your rig look put together, yet change it instantly with No Tools and No Waste.

The 9-piece Base Kit is the ideal starting point for cabling your rig. You get a total of six clips for the larger 1.25 inch tubes (including two extended-capacity clips), and three smaller clips for the 1.0 inch mouse-platform vertical riser tube. The 9-pc Base Kit is available in black or white.

Most people find they need around a dozen total of the 1.25 clips, so a 1.25 6-pc expansion pack gets you there. Personalize your rig with 1.2 expansion pack in a variety of colors and combinations.

If all that doesn't get you enough cabling capacity, there's the Large Capacity Kit. With four 1.25" and two 1.0" plusBack clamps in black or white, you get a total (with the original Base Kit clips) or nearly three times the capacity! That's a whole lotta wiring.

And lastly, if you have more cables going up to the side platforms, you can add a 1.0 3-pc expansion pack, in black or white.

Note: The oZone and R3volution models use the same diameter tubes, but in significantly differenty configurations. It's expected that you'd typically use fewer clips on the oZone. But, system variability is larger than the structural difference, so the result is: get what you need. 😉




How much can they hold?


6+ Power Cords? Yeah Right...prove it!


The cable areas in the clips for tubing diameters 1.0 inch and above are designed to hold at least 7 typical "SVT" power cords (UL-Type SVT, 3C/18AWG 300V, ~6mm in diameter).

On the OR3V models, the Base Kit has parts to manage cables on both sides of the rig, so expect 12-16 "power cord equivalents" (PCE) total capacity on the rig, front-to-back. Up the thruster mount / mouse platform you'll get about 6-7 PCE.

The 1.25 Expanded Capacity clips have a secondary channel, sized for ~4 16AWG two-conductor speaker cables, in addition to the 8 SVTs on the other side.

"Well yeah, but my cables are HEAVY!" The thing to remember is that no component is ever infinitely strong, nor will anything (besides time itself) last forever. The same is true with 4CELNK-YR clips. There is some large amount of force that will break them. I haven't reached it yet, but it's not at all impossible to yank on a cable and pull it out of the clip. (If you're going to be violently pulling the cables, then maybe stick with tie-wraps)

From what I've been able to tell, "a couple pounds" (~1kg) is just fine as far as holding strength. I might be inclined to add more bands (5-6 instead of 3-4) up to about 5 pounds (2.2 kg), but beyond that weight you should consider adding more clips. A typical "good" straight run of 6+ ethernet cables would normally have a clip about every 3-4 feet (~1 meter) or so, more if the cables need more support.

But, beware: if you put only one clip every 8 feet, and expect it to hold 20 pounds, that will very likely end in disaster...and the warranty won't cover it.




Warnings & Cautions


View More...


Please keep the following in mind when using 4CELNK-YR cable clips:

Watch for damaged, worn, frayed or otherwise dangerous cables, and replace all that are unsafe.

Dangling, partially-secured cords beneath desks, tables, and in shelving can in some instances present electrocution and strangling hazards. Be wary!

The 4CELNK-YR arms are closely spaced, and there is spring tension holding them together. Use with care to avoid getting pinched or struck by the arms.

4CELNK-YR Cable Clips are not UL-Listed, they are not specially plenum-rated, nor are they flame-retardant.

4CELNK-YR Cable Clips are not a "safety device".

4CELNK-YR Cable Clips are not specially treated for UV-resistance. Using 4CELNK-YR outdoors, or in a high-UV environment can cause them to age more quickly, and, ultimately, fail sooner.

4CELNK-YR Cable Clips, including the Rack Series, have not been NSF-certified for use in commercial kitchens.

4CELNK-YR cable clips are made from ABS plastic: tough, but not unbreakable. Don't overload the clips.

There may be other hazards associated with your doing with cables whatever it is you're doing. Please always be aware of your surroundings, and be careful.




Easy-Change Cable Management...
...with NO Tools and NO Waste


See the complete 4CELNK product line-up...

4CELNK-YR flatBack Series


Cables! They're stuffed underneath and behind the desk, the TV and video center, and every other electronic system at home and work. Cables are everywhere! Fix that desk-side mess with stick-on, No Waste 4CELNK-YR flatBack series cable clips.

4CELNK-YR Rack Series


Wire shelving racks are used in the home, office, greenhouse, and industrial settings. Route cables neatly along the poles, under or over the shelves, in configurations large and small, with 4CELNK-YR Rack series kits and packs.

4CELNK-YR Tubing Series


Electrical-Mechanical Tubing (EMT) is commonly used in construction and picnic/event canopies. Keep those one-time events from producing permanent tie-wrap waste with reusable, No Waste 4CELNK-YR Tubing series cable clips.

4CELNK-YR OR3V Series


The 4CELNK-YR OR3V Series is specially designed to fit the Obutto R3volution and oZone gaming rigs. By keeping the cables up tight against the rig tubes, they stay nice and neat, and don't get tangled. Your cabling will thank you every race with 4CELNK-YR OR3V series cable clips.

4CELNK OR3V LFE Mounts


Mount ButtKicker Mini-LFEs to your rig, and feel the gaming like never before. Machined aluminum 4CELNK LFE mounts are available in pairs and sets of four or 5.



4CELNK products are manufactured in Washington state, USA

4CELNK.com Site Map
Surfaces
9-Pc Starter Kit
12-pc Small Pack
6-pc Large Pack
Wire Racks
10-Pc 1-Tier Kit
1.0 8-pc Pack
0.25 8-pc Pack
0.25 LgCap. 8-pc Pk
Tubing
0.5 10-Pack
0.75 10-Pack
1.0 10-Pack
1.25 10-Pack
SimRigs
9-pc Base Kit
1.25 6-pc Exp. Pk
1.0 3-pc Exp. Pk
Lg Cap 6-pc Kit
LFE Mounts
Set of 5 (2F 3R)
Set of 4 (2F 2R)
Rear Pair
Front Pair
Support
Blog
Contact Us
Warranty
Privacy Policy
Terms of Use
About Us