Gather and conquer all those cables heading up to the mouse platform and desk with these 4CELNK-YR OR3V 1.0 clips.
Didn’t they say everything would be wireless by now, and we’d have flying cars? Yeah, I don’t have one yet, either. Which means that yes, some keyboards (the good kind) still have cables. Same with thrust controllers. And gaming pedals. And e-brakes, and shifters, and and and…. Get yourself a set or two of these and make those articulating-surface cables a non-issue.
4CELNK-YR OR3V 1.0 3-pc Expansion Pack - WHT (2018-027-103-WHT)Photo coming soon....
3 x 4CELNK-YR noBack 1.0 Cable Clamp - WHT
1 x 4CELNK-YR Small Bag-O-Bands
1 x 4CELNK-YR OR3V 1.0 Expansion Pack - WHT - Package Insert
Made to fit oZone and R3volution sim rigs
Finally! Gaming rig cable management that's easy to put on, easy to change, and easy to live with. Imagine: no more cutting and replacing wire-ties. No more scratching the rig. Now you can have your rig look put together, yet change it instantly with No Tools and No Waste.
The 9-piece Base Kit is the ideal starting point for cabling your rig. You get a total of six clips for the larger 1.25 inch tubes (including two extended-capacity clips), and three smaller clips for the 1.0 inch mouse-platform vertical riser tube. The 9-pc Base Kit is available in black or white.
Most people find they need around a dozen total of the 1.25 clips, so a 1.25 6-pc expansion pack gets you there. Personalize your rig with 1.2 expansion pack in a variety of colors and combinations.
If all that doesn't get you enough cabling capacity, there's the Large Capacity Kit. With four 1.25" and two 1.0" plusBack clamps in black or white, you get a total (with the original Base Kit clips) or nearly three times the capacity! That's a whole lotta wiring.
And lastly, if you have more cables going up to the side platforms, you can add a 1.0 3-pc expansion pack, in black or white.
Note: The oZone and R3volution models use the same diameter tubes, but in significantly differenty configurations. It's expected that you'd typically use fewer clips on the oZone. But, system variability is larger than the structural difference, so the result is: get what you need. 😉
How much can they hold?
6+ Power Cords? Yeah Right...prove it!
On the OR3V models, the Base Kit has parts to manage cables on both sides of the rig, so expect 12-16 "power cord equivalents" (PCE) total capacity on the rig, front-to-back. Up the thruster mount / mouse platform you'll get about 6-7 PCE.
The 1.25 Expanded Capacity clips have a secondary channel, sized for ~4 16AWG two-conductor speaker cables, in addition to the 8 SVTs on the other side.
"Well yeah, but my cables are HEAVY!" The thing to remember is that no component is ever infinitely strong, nor will anything (besides time itself) last forever. The same is true with 4CELNK-YR clips. There is some large amount of force that will break them. I haven't reached it yet, but it's not at all impossible to yank on a cable and pull it out of the clip. (If you're going to be violently pulling the cables, then maybe stick with tie-wraps)
From what I've been able to tell, "a couple pounds" (~1kg) is just fine as far as holding strength. I might be inclined to add more bands (5-6 instead of 3-4) up to about 5 pounds (2.2 kg), but beyond that weight you should consider adding more clips. A typical "good" straight run of 6+ ethernet cables would normally have a clip about every 3-4 feet (~1 meter) or so, more if the cables need more support.
But, beware: if you put only one clip every 8 feet, and expect it to hold 20 pounds, that will very likely end in disaster...and the warranty won't cover it.
Installing 4CELNK-YR Cable Clips
Gently spread the arms and slide clip over tube. Avoid Twisting the clip. (View More...)
IMPORTANT: Don't spread the arms out too far! The more you bend them, and the more often you bend them, the more they will lose their "spring" over time. Yes, they can actually be spread quite large and they will "work" afterwards. But, never as well as before being over-stressed.
Setting the 4CELNK-YR Holding Tension
Add bands from the included Bag-O-Bands to get the tension just right. (View More...)
The clips should stay in place and adequately hold the cables that you plan to use. 3 is typical, going to 5 or more when the clip is full.
If you need to later change the number of bands, just pull any captured cables out, add the other bands, then put them all back in again. Easy, with Zero Waste!
Some users report not needing to use any bands at all; that will work well for few shaker cables, or just a couple USB cables. Add more bands for larger bunches, or where you want the bundles to stay in place a little better. There should be enough provided so you get about 5 bands per piece in the package.
TIP: The bands that ship with 4CELNK-YR are actually children's 1" hair bands: they're cheap, and available most everywhere. If you want everything really locked down, with a little "security", you could even use...gasp!...a tie wrap.
Adding and Removing Cables
Adding CablesNow comes the easy part!
Removing CablesHere's where it gets impossible for tie-wraps...
CAUTION: If you pull the cable out too quickly from the capture area, the inside arm might snap back and hit your fingertips.
Warnings & Cautions
Watch for damaged, worn, frayed or otherwise dangerous cables, and replace all that are unsafe. Dangling, partially-secured cords beneath desks, tables, and in shelving can in some instances present electrocution and strangling hazards. Be wary! The 4CELNK-YR arms are closely spaced, and there is spring tension holding them together. Use with care to avoid getting pinched or struck by the arms. 4CELNK-YR Cable Clips are not UL-Listed, they are not specially plenum-rated, nor are they flame-retardant. 4CELNK-YR Cable Clips are not a "safety device". 4CELNK-YR Cable Clips are not specially treated for UV-resistance. Using 4CELNK-YR outdoors, or in a high-UV environment can cause them to age more quickly, and, ultimately, fail sooner. 4CELNK-YR Cable Clips, including the Rack Series, have not been NSF-certified for use in commercial kitchens. 4CELNK-YR cable clips are made from ABS plastic: tough, but not unbreakable. Don't overload the clips.
There may be other hazards associated with your doing with cables whatever it is you're doing. Please always be aware of your surroundings, and be careful.
Watch for damaged, worn, frayed or otherwise dangerous cables, and replace all that are unsafe.
4CELNK-YR Cable Clips are not a "safety device".
Easy-Change Cable Management...
|4CELNK-YR flatBack Series|
|4CELNK-YR Rack Series|
|4CELNK-YR Tubing Series|
|4CELNK-YR OR3V Series|
|4CELNK OR3V LFE Mounts|